Power & Energy

RM 3.6K
In-House Training - Basic Troubleshooting on Balance…
Power & Energy

2 Days

View Details

Overview:

This course is designed to improve participant’s know how to observe best operation practices for effective operation. The trainers will guide and facilitate the participants through examples of some operations common problems.

Participants shall be introduced to diesel engine and gas turbine in a typical power plant along with their respective auxiliaries and working principles. The trainer will guide participants on some of the common problems in the operation of both units and trouble-shooting will be also discussed.


Objective:

• Explain the best operation practices in Diesel & Gas Turbine Auxiliaries.
• List down the common problems encountered during operation of both the plant’s auxiliaries.
• Explain the steps taken for basic troubleshooting on the problems encountered.
• Make a chart on Common problems – Causes – Action taken.


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.com.my
 
 



Target Participant: Operation Engineers, Gas Turbine Operators, Steam Plant Operators & anyone who has interest to the related subject
Duration: 2 Days
Language:

RM 3.6K
In-situ and Machine Shop Balancing (Practical)
Power & Energy

3 Days

View Details

Overview:
This course will cover basic to rigid rotor shop balancing subjects such as unbalance types of Static, Couple & Dynamic, balancing speed & critical speed, flexible & rigid, shop balancing. Participants will learn also Machine Shop balancing setup & operation via hands on work on an impeller of a single stage pump & a small turbine rotor using 2 plane dynamic correction.
 
Participants will learn how to calculate ISO 1940/1 standards, namely the common G6.3 & G4.5 grading of Permissible Residual Unbalance. Also covered are how to combining weights, and splitting weights at designated balancing locations.
 
Also touched are vibration signature analysis to determine genuine unbalance affected machinery. Participants will learn how to setup and read key phaser and vibration probes to perform single plane balancing in-situ using polar charts and vector calculations. All training is hands on with real rotors at our workshop.
Objective:

  • Able to explain Static, Couple, & Dynamic Unbalance
  • Able to perform machine shop 1 & 2 plane balancing
  • Able to calculate residual unbalance under ISO 1940/1
  • Perform In-situ balancing using a vibration analyzer & single plane vector trial weight method
  • Able to identify characteristic of actual unbalance dominant vibration signatures


for any enquiries please contact:

1. NAME: CHOOI WAI MUN
   Email: chooiwm@tnb.com.my

2. NAME: ABDUL RAZAK
   Email: razakm@tnb.com.my

Target Participant: TNBG Mechanical Maintenance
Duration: 3 Days
Language: English, Malay

RM 3.6K
Industrial Radiography Safety
Power & Energy

3 Days

View Details

Overview:
This course is designed to explain the basic criteria for provide better understanding of the philosophy and principles of industrial radiography, radiation safety and protection; create awareness on biological effects and the risk of ionizing radiation. Learn the right procedure when dealing with ionizing radiation, acquire the techniques and proper procedures in controlling the radiation exposure to the radiation workers and explain the regulation of radiation protection and legislative requirements.
 
The training format is theory and practical, where the participants will be actively involved in the class & practical activities. Hence, it will increase their confidence level.

Participant will be taken through the vast experience of industrial radiography procedure and performance by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
After attending this training program, participants will be able to:

  1. Provide better understanding of the philosophy and principles of industrial radiography, radiation safety and protection. 
  2. Create awareness on biological effects and the risk of ionizing radiation.
  3. Learn the right procedure when dealing with ionizing radiation
  4. Acquire the techniques and proper procedures in controlling the radiation exposure to the radiation workers.
  5. Explain the regulation of radiation protection and legislative requirements.


for any enquiries please contact:

1. NAME: AMIR ABU
   Email: amira@tnb.com.my

Target Participant: Technicians, Mech. Engineers, Mech. Executives & Mech. Non-Executives
Duration: 3 Days
Language: English, Malay

RM 3.6K
Infra-Red Thermography - Level 1
Power & Energy

4 Days

View Details

Overview:
A picture says a thousand words;- this course of infrared thermography helps participants to harness IR technology to visualize thermal performance, show thermal anomalies, verify fault and quantify them with precise non-contact temperature measurement.

Infrared is NOT a “point and shoot” device as many IR manufacturers would like you to believe! Participants shall understand fundamentals behind infrared devices to use it appropriately. Erroneous technique and interpretation has very little value and gives Infrared thermography a bad name.

Here at ILSAS, IR training lesson will be reinforced with actual hands-on attempted by for participants themselves. All theory will be correlated to relevance to on site inspection. The training will be complete with not only examination but also a real live practical IR inspection at a TNB substation and a comprehensive report.
Objective:
Upon completion of this workshop, participants will be:

  • Able to operate an Infrared (IR) Thermography camera to find thermal anomalies
  • Able to interpret an IR image correctly to find real fault
  • Able to execute proper reporting & documentation with correct IR emissivity & reflected apparent temperature
  • Able to understand heat transfer & basic thermal science

for any enquiries please contact:

1. NAME: ABDUL RAZAK
   Email: razakm@tnb.com.my

Target Participant: TNBG, TNBT, TNBD Executives in Operation & Maintenance
Duration: 4 Days
Language: English, Malay

RM 3.6K
Internal Combustion Engine (ICE) Driver Grade 1
Power & Energy

4 Days

View Details

Overview:
This course offers for participants to equipped with relevant knowledge and skill to sit for Internal Combustion Engine (ICE) Driver Grade 1 test, conducted by Department of Occupational Safety and Health (DOSH). Its consists of Act and Regulations (FMA Act 139 & OSHA Act 514); Gas turbine introduction (history, steam cycles, types and classification of gas turbine); Diesel engine introduction (history, steam cycles, types and classification of diesel engine); Gas turbine main components and their functions; Gas turbine and its auxiliary system; Diesel engine and its auxiliary system; Principle operation of gas turbine and diesel engine; Maintenance concept on gas turbine and diesel engine; Troubleshooting of gas turbine operation; Trouble shooting of diesel engine operation; Simulation of actual DOSH exam interview.
Objective:
At the end of the course, participants will be:

Equipped with relevant knowledge and skill to sit for Internal Combustion Engine Driver Grade 1 test, conducted by Department of Occupational Safety and Health (DOSH) such as:

  • Act and Regulations (FMA Act 139 & OSHA Act 514
  • Oral examination skill
  • Basic operation of gas turbine and diesel engine
  • Identification of the components of gas turbine and their functions
  • Identification of the components of diesel engine and their functions
  • Troubleshooting of gas turbine and diesel engine operation
Able to implement proper safety procedures in carrying out gas turbine and diesel engine operations and maintenances

Target Participant: ICE Driver Candidate
Duration: 4 Days
Language: English, Malay

RM 3.6K
Internal Combustion Engine (ICE) Driver Grade 1*
Power & Energy

4 Days

View Details

Overview:
This course offers for participants to equipped with relevant knowledge and skill to sit for Internal Combustion Engine (ICE) Driver Grade 1 test, conducted by Department of Occupational Safety and Health (DOSH). Its consists of Act and Regulations (FMA Act 139 & OSHA Act 514); Gas turbine introduction (history, steam cycles, types and classification of gas turbine); Diesel engine introduction (history, steam cycles, types and classification of diesel engine); Gas turbine main components and their functions; Gas turbine and its auxiliary system; Diesel engine and its auxiliary system; Principle operation of gas turbine and diesel engine; Maintenance concept on gas turbine and diesel engine; Troubleshooting of gas turbine operation; Trouble shooting of diesel engine operation; Simulation of actual DOSH exam interview.


 


Objective:
At the end of the course, participants will be:

Equipped with relevant knowledge and skill to sit for Internal Combustion Engine Driver Grade 1 test, conducted by Department of Occupational Safety and Health (DOSH) such as:
  • Act and Regulations (FMA Act 139 & OSHA Act 514)
  • Oral examination skill
  • Basic operation of gas turbine and diesel engine
  • Identification of the components of gas turbine and their functions
  • Identification of the components of diesel engine and their functions
  • Troubleshooting of gas turbine and diesel engine operation
Able to implement proper safety procedures in carrying out gas turbine and diesel engine operations and maintenances.


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.com.my

Target Participant: • Gas turbine and diesel engine operators, patrolmen, lab technicians and others who obtained ICE Driver Grade 2 and wish to sit for the ICE Driver Grade 1 exam by the Department of Occupational Safety and Health (DOSH) • Those who are interested to deepen their knowledge about the subject
Duration: 4 Days
Language:

RM 3.6K
Internal Combustion Engine (ICE) Driver Grade 2
Power & Energy

4 Days

View Details

Overview:
This course offers for participants to equipped with relevant knowledge and skill to sit for Internal Combustion Engine (ICE) Driver Grade 2 test, conducted by Department of Occupational Safety and Health (DOSH). Its consists of Act and regulation (FMA Act 139 & OSHA Act 514); Gas turbine introduction (history, types and classification of gas turbine); Diesel engine introduction (history, types and classification of gas turbine); Gas turbine/diesel engine components and their functions; Gas turbine/diesel engine maintenance; Principle operation of gas turbine and diesel engine; Non-Destructive Testing, welding; Simulation of actual DOSH exam interview.
Objective:
At the end of the course, participants will be able to:

  • Explain related provisions under the Factories and Machinery Act 1967, and regulations together with the Occupational Safety and Health Act 1994.
  • Explain the working principles of various types of gas turbine system and their cycles (e.g. compressor, turbine, combustor, their fittings/control equipment).
  • Explain the operation of gas turbine (e.g. start-up, synchronizing, supervision and protection, shutdown).
  • Explain the working principles of various types of diesel engine.
  • Explain the operation of diesel engine (e.g. start-up, synchronizing, supervision, protection and shutdown
  • Describe type of maintenance (e.g. description on routine, daily, preventive and major).
  • Achieve simulated experience for actual DOSH examination


Target Participant: ICE Driver Candidate
Duration: 4 Days
Language: English, Malay

RM 3.6K
Internal Combustion Engine (ICE) Driver Preparatory…
Power & Energy

2

View Details

Overview:

Objective:


Target Participant: ICE Driver Candidate
Duration: 2
Language:

RM 3.6K
Internal Combustion Engine (ICE) Engineer Grade 1
Power & Energy

4 Days

View Details

Overview:
This course offers for participants to equipped with relevant knowledge and skill to sit for Internal Combustion Engine (ICE) Engineer Grade 1 test, conducted by Department of Occupational Safety and Health (DOSH). Its consists of Act and Regulations (FMA Act 139 & OSHA Act 514); Review gas turbine introduction (history, types and classification of gas turbine); Review diesel engine introduction (history, types and classification of combustion engine); Internal combustion engine operation including cogeneration principle and compressor operation; Plant maintenance and policy formulation; Plant management and administration; Troubleshooting of gas turbine operation; Trouble shooting of diesel engine operation; Simulation of actual DOSH exam interview.
Objective:
At the end of the course, participants will be able to:

  • Describe and comprehend the Act and Regulations (FMA Act 139 & OSHA Act 1994)
  • Synthesize the Act and Regulation into actual operation practice
  • Describe the operation procedure of gas turbine and diesel engines including identification of critical components of Internal Combustion Engine machine
  • Identify and evaluate the plant management and troubleshooting process of gas turbine and diesel engine
  • Achieve simulated experience for actual DOSH examination


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.ccom.my

Target Participant: ICE Engineer Candidate
Duration: 4 Days
Language: English, Malay

RM 3.6K
Internal Combustion Engine (ICE) Engineer Preparatory…
Power & Energy

2

View Details

Overview:

Objective:


Target Participant: ICE Engineer Candidate
Duration: 2
Language:

RM 3.6K
Introduction to Energy Management
Power & Energy

2 Days

View Details

Overview:

The course is designed to give participant’s basic knowledge about Energy Management and the system. It is Incorporates the theory and simple practical energy auditing and solution development, as well as regulations and standards.

This course will provide a basic electrical energy management guide and practical application. It will cover the fundamental principles, practical energy conservation checklist guidelines and energy saving measure. A basic Energy Management System is also being discussed in this two days course.
 


Objective:
Upon completion of this course, participants will be able to:
  • Describe the Global and Malaysian Energy Scenario
  • Describe TNB's Vision and Mission in energy context
  • Familiarize Policy, Acts and Regulations in existence in Malaysia and other countries
  • Identify energy saving potential for appliances
  • Identify energy saving measures in term of energy efficient rating and labeling

for any enquiries please contact:

1. NAME: IR. WAN AMINUDDIN BAKI BIN ABDUL KHALID
   Email: aminuddinak@tnb.com.my

2. NAME: ANNAS BIN AHMAD SALLEH
   Email: annass@tnb.com.my

Target Participant: Technical & Non-Technical Executive in Government, Government Agencies & Private Sector
Duration: 2 Days
Language: English, Malay

RM 3.6K
Introduction to Mechanical Components (TT05-TT06)
Power & Energy

3 Days

View Details

Overview:
The workshop is designed to improve participant’s knowledge to handle maintenance work related to pumps, compressors, and valve. The trainers will guide and facilitate the participants through examples and demonstration on physical pumps, compressors, and valves at ILSAS workshop.

Participants shall be introduced to various types of pump, compressors, and valves in a typical power plant along with their respective major components and working principles. Selection of suitable type of pump, compressor, and valve will be discussed along with common periodic maintenance practice and typical maintenance problems.
Objective:
Upon completion of this workshop, participants will be:

  • Describe the principle of the following components:
  1. Pump
  2. Compressor
  3. Valve
  • Describe the basic differences of those items type.
  • Describe the major components of those items.
  • Describes the basic of troubleshooting.

for any enquiries please contact:

1. NAME: CHOOI WAI MUN
   Email: chooiwm@tnb.com.my

2. NAME: JALIL ARRIFIN
   Email: jalila@tnb.com.my

Target Participant: Mechanical TNBG Assistant Tech (TT05-TT06)
Duration: 3 Days
Language: English, Malay

RM 3.6K
Introduction to Non-Destructive Testing
Power & Energy

5 Days

View Details

Overview:
This course covers applications associated with four (4) main types of Non Destructive Testing and offers a high practical content and relevant theoretical background to enable course participants to achieve the understanding of NDT.

The training format is theory and practical, where the participants will be actively involved in the class and practical activities. Hence, it will increase their confidence level.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experience of training by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the Course.
Objective:
After attending this program, participants will be able to:

  • Identify / enumerate four (4) main types of NDT inspection methods used in power plant inspection.
  • Select the most appropriate NDT method / technique for the inspection of power plant components in accordance to relevant code and standards.


for any enquiries please contact:

1. NAME: AMIR ABU
   Email: amira@tnb.com.my

Target Participant: TNBG TT09-TT13, Mech. Engineers & Mech. Executives
Duration: 5 Days
Language: English, Malay

RM 3.6K
Kraftwerk-Kennzeichen System (KKS) Coding
Power & Energy

2 Days

View Details

Overview:

Kraftwerk-Kennzeichen System (KKS) serves to unambiguously identify plants, sections of plants and items of equipment in any type of power station according to task, type and location. It is applicable to all engineering disciplines (e.g. process, civil, electrical, instrumentation and control engineering). It is used for planning, licensing, construction, operation & maintenance, re-powering and upgrade, demolition & recycling. In other words, it is a sole designation system lasting for the whole lifecycle of a power plant and all its systems, equipment and components.

To planning, setting-up and operating power plants it is absolutely necessary to use a standardized identification system. The "Kraftwerk-Kennzeichen System (KKS)" is such a system.


Objective:

Terminal Objective:

With the Kraftwerk-Kennziechen Sysytem (KKS) Coding Reference given, the participant will be able to develop KKS codes from the Piping/Process & Instrumentation Diagram (P&ID) given

Course Objectives:

On completion of the course, participant will be able to:

  • To explain the purpose KKS Codes
  • List all breakdown levels of a KKS Codes
  • To develop process related code for power plant


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI B. MOHD SALLEH
     Email: khairul.fikri@tnb.com.my
 
 



Target Participant: TT07 - 10
Duration: 2 Days
Language:

RM 3.6K
Kraftwerk-Kennziechen System (KKS) Coding
Power & Energy

2 Days

View Details

Overview:
Kraftwerk-Kennzeichen System  (KKS) serves  to  unambiguously  identify  plants,  sections  of plants  and  items  of  equipment  in  any  type  of  power  station  according  to  task,  type  and location.  It  is  applicable  to  all  engineering  disciplines  (e.g.  process,  civil,  electrical, instrumentation  and  control  engineering).  It  is  used  for  planning,  licensing,  construction, operation & maintenance, re-powering and upgrade, demolition & recycling.

In other words, it  is  a  sole  designation  system  lasting  for  the  whole  lifecycle  of  a  power  plant  and  all  its systems, equipment and components.

To  planning,  setting-up  and  operating  power  plants  it  is  absolutely  necessary  to  use  a standardized  identification  system.  The  "Kraftwerk-Kennzeichen System  (KKS)"  is  such  a system.
Objective:
Terminal Objective:

With the Kraftwerk-Kennziechen Sysytem (KKS) Coding Reference
given, the participant will be able to develop KKS codes from the
Piping/Process & Instrumentation Diagram (P&ID) given

Course Objectives:

On completion of the course, participant will be able to:
· To explain the purpose KKS Codes
· List all breakdown levels of a KKS Codes
· To develop process related code for power plant


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.com.my

Target Participant: TNB Generation Technician TT07-TT10 & those who are interested to deepen their knowledge about the subject
Duration: 2 Days
Language:

RM 3.6K
Latihan Audit Tenaga di Bangunan - SEDA
Power & Energy

3.5 Days

View Details

Overview:
An energy audit is an inspection, survey and analysis of energy flows for energy conservation in a building, process or system to reduce the amount of energy input into the system without negatively affecting the output(s).

When the object of study is an occupied building then reducing energy consumption while maintaining or improving human comfort, health and safety are of primary concern. Beyond simply identifying the sources of energy use, an energy audit seeks to prioritize the energy uses according to the greatest to least cost effective opportunities for energy savings.

In this course participant will gain better understanding on energy sources, supply & demand trends, policies, regulatory structure and energy efficiency potentials in Malaysia others than core of courses which is energy audit in building.
Objective:

  • Identify energy saving potential and initiatives in building sector
  • Provide basic understanding of measurement for Energy Audit

for any enquiries please contact:

1. NAME: IR. WAN AMINUDDIN BAKI BIN ABDUL KHALID
   Email: aminuddinak@tnb.com.my

2. NAME: ANNAS BIN AHMAD SALLEH
  Email: annass@tnb.com.my

Target Participant: Technical & Non-Technical Executive in Government, Government Agencies & Private Sector
Duration: 3.5 Days
Language: English, Malay

RM 3.6K
Latihan Pengurusan Kecekapan Tenaga Sistem Penyaman…
Power & Energy

2 Days

View Details

Overview:
Energy Efficiency Management of Air-Conditioning and Mechanical Ventilation (ACMV) System training will give technical exposure specifically for the efficient management of ACMV system to reduce the operation cost and energy consumption of buildings.

Participants will enhance their knowledge in ACMV System operation as other training in local market, but this training have added value in term of efficient management of the system as a measure to monitor energy consumption of their building.

The training will provide energy efficient management tips or measures for each equipment in ACMV system in providing sustainable system operation throughout the life time of the building.
Objective:

  • To increase awareness on the energy efficiency practices and saving measures in building ACMV system for building operators
  • To provide knowledge on efficient management of ACMV system
  • To provide knowledge on types of ACMV System Design and Selection
  • To provide understanding of ACMV Cooling Load and Load Profile


for any enquiries please contact:

1. NAME: IR. WAN AMINUDDIN BAKI BIN ABDUL KHALID
   Email: aminuddinak@tnb.com.my

2. NAME: ANNAS BIN AHMAD SALLEH
   Email: annass@tnb.com.my

Target Participant: Technical & Non-Technical Executive in Government, Government Agencies & Private Sector
Duration: 2 Days
Language: English, Malay

RM 3.6K
Latihan Pengurusan Tenaga Di Bangunan - SEDA
Power & Energy

3 Days

View Details

Overview:
Module was developed according to International Organization for Standardization ISO 50001, Energy Management Standard (EnMS). Module was designed in such a way provides a method for integrating Energy Efficiency into existing building management systems for continual improvement.

Participant will gain better understanding on energy sources, supply and demand trends, policies, regulatory structure and energy efficiency potentials in Malaysia others than core of courses which is energy management in building.
Objective:

  • Increase understanding of residents and facility managers on energy management in buildings
  • Provide platform among public servants and private sector to get involved in energy efficiency and energy management in buildings
  • Provide basic eligibility to implement a comprehensive energy efficiency projects and energy savings through energy management measures on building systems
  • Enable basic understanding on energy management to public and private sector before joining into more complete technical training


for any enquiries please contact:

1. NAME: IR. WAN AMINUDDIN BAKI BIN ABDUL KHALID
   Email: aminuddinak@tnb.com.my

2. NAME: ANNAS BIN AHMAD SALLEH
   Email: annass@tnb.com.my

Target Participant: Technical & Non-Technical Executive in Government, Government Agencies and Private Sector
Duration: 3 Days
Language: English, Malay

RM 3.6K
Low Voltage Switching and Protection
Power & Energy

3 Days

View Details

Overview:
The course is to improve participant’s ability to do switching for supply auxiliaries to start up and shutdown the generator in power plant. The trainers will guide and facilitate the participants to do exercise with simulator, so that they can to improve their ability to do switching with no interuption.

The training format is theory and practical, whereby the participants will be actively involved in the class activities to increase their confidence level.
Objective:
Upon completion of this course, participants will be able to:

  • Describe and identify the house supply board arrangement and the operating voltage
  • Identify the various auxiliary board
  • Identify the source of supply to boards
  • Identify the emergency board and its feeders
  • Interpret the single line diagram

accurately by referring to slides / notes given.


for any enquiries please contact:

1. NAME: ABDUL HISHAM ABDUL HALIM
   Email: ahisham.ahalim@tnb.com.my

2. NAME: YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

Target Participant: TT09 - Non-Executive (Generation)
Duration: 3 Days
Language:

RM 3.6K
Machineshop Balancing
Power & Energy

2 Days

View Details

Overview:

This course will cover basic to rigid rotor shop balancing subjects such as unbalance types of Static, Couple & Dynamic, balancing speed & critical speed, flexible & rigid, shop balancing. Participants will learn also Machine Shop balancing setup & operation via hands on work on an impeller of a single stage pump & a small turbine rotor using 2 plane dynamic correction.

This course will introduce proper calculation to adhere to ISO 1940/1 standards, namely the common G6.3 & G4.5 grading of Permissible Residual Unbalance. Also covered are how to combining weights, and splitting weights accordingly at designated balancing locations.


Objective:
Upon completion of this workshop, participants will be:

• Able to differentiate Static Unbalance, Couple Unbalance, & Dynamic Unbalance
• Perform machine shop balancing using 1 & 2 plane corrections
• Calculate correct residual unbalance for a given rotor under ISO 1940/1


for any enquiries please contact:

1. NAME: CHOOI WAI MUN
   Email: chooiwm@tnb.com.my

2. NAME: ABDUL RAZAK
   Email: razakm@tnb.com.my
 

Target Participant: TNBG TT11-TT13 Mechanical Maintenance
Duration: 2 Days
Language: English, Malay

RM 3.6K
Main Plant Maintenance Works
Power & Energy

5 Days

View Details

Overview:
This course is a compressed and concise hands-on on common works related to main power plant maintenance works. Every individual topic is demonstrated by instructor via hands-on and practical of actual work. This course does not replace individual full courses which details calculation, actual theory, and skill developments set.

Covered actual practical works alone without any comprehensive classroom theory. The work involves Steam Turbine Inspection, Overhaul of a Pump, Erection of a Scaffolding (Tubular Type), Overhaul of a Safety Valve Maintenance, and Bearing Journal Inspection.
Objective:
Upon completion of this workshop, participants will be:

• Describe various types of main plant maintenance works
• Identify the main components
• Describe the functions of components
• Describe type of inspection
• Describe routine maintenance


for any enquiries please contact:

1. NAME: CHOOI WAI MUN
   Email: chooiwm@tnb.com.my

2. NAME: ABDUL RAZAK
   Email: razakm@tnb.com.my

Target Participant: TNBG Engineers in Mechanical Maintenance
Duration: 5 Days
Language:

RM 3.6K
Maintenance of Control and Instrumentation Measuring…
Power & Energy

3 Days

View Details

Overview:
The course is designed to improve participant’s skill to Calibration and maintenance of Control and Instrumentation equipment in their’s working place.

The training format is on theory and practical, where the participants will be actively involved in the lab activities.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experiences of training by the trainer. The emphasis is on participants continuing participation in ensuring the ultimate success in the course.
Objective:
After attending this training program, participants will be able to:

  • Define types of maintenance.
  • Define the safety equipment and why they are needed in the workplace.
  • Classified job according to maintenance needed.
  • Explain and do the calculation of basic calibration.
  • Explain the principal of measurements.
  • Know and differentiate the function of measuring equipments / instruments.
  • Do the calibration work.
 
Without any mistake.


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: TAN BENG WEE
   Email: tanbw@tnb.com.my

Target Participant: Control & Instrumentation personnel TT09-TT10 & individuals or technicians involved in maintenance of process measurement
Duration: 3 Days
Language: English, Malay

RM 3.6K
Maintenance, Inspection and Testing of Electrical…
Power & Energy

5 Days

View Details

Overview:
This course provides a comprehensive knowledge about electrical maintenance in power plant, primarily focusing on generator, excitation, circuit breaker, Uninterruptible Power Supply (UPS) and power transformer. The goal of the course is to give new electrical engineers to familiarize the standard procedures of electrical maintenance and testing for electrical equipment in power plant.

The training methodology is theory and group discussion, where the participants will be actively involved in the class activities.
Objective:
Upon completion of this course, participants will be able to:

• Locate and rectify electrical equipment related problems in power station
• Describe the standard practice of maintenance, inspection and testing of electrical equipment


for any enquiries please contact:

1. NAME: YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: SOH LEY BAU
   Email: sohlb@tnb.com.my
 

Target Participant: Electrical Engineer & Electrical Executive
Duration: 5 Days
Language:

RM 3.6K
Mobile Genset Operation
Power & Energy

5 Days

View Details

Overview:
This course covers working environment & personal safety, mobile generators and diesel engine functions and operation. It include preparation and pre-start check of genset, termination, checking before start up, start up mobile genset  & give supply, testing, checking during operation, shut down mobile genset, checking after shut down and disconnect termination.

The goal of the course is to familiarize mobile genset operation personal of the responsibilities and working environment of inspection, monitoring, operation of the genset as well as to do termination and giving supply to the consumer within the time frame in correct and safe manner.

The trainers will guide and facilitate the participants. The training format is theoretical class and practical training.
Objective:

Upon completion of this course, participants will be able to:

• Describe the safety of the work environment & personal
• Describe the diesel engine main components and functions
• Describe the generator main components and functions
• Describe mechanical and electrical low voltage protection
• Able to do inspection / monitoring / operation in correct and safe manner
• Able to run genset and monitor the operating parameters

 accurately by referring to slides / notes given.


for any enquiries please update:

1. NAME: ABDUL HISHAM ABDUL HALIM 
   Email: ahisham.ahalim@tnb.com.my

2. NAME: YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my
 



Target Participant: TNB Generation Technician, TNB Distribution Technician, TNB Logistic (Corporate) & Genset Operation Personnel
Duration: 5 Days
Language:

RM 3.6K
Motor Maintenance And Testing
Power & Energy

2 Days

View Details

Overview:
The course provides a comprehensive knowledge about the Motor Maintenance and Testing in power plant and industry environment. The targeted audience of this course are power plant electrical engineers, facility engineers and technical supervisors whose jobs involve in the maintenance of electrical motor.

This course covers the competency requirements to recognize, diagnose and remedy an evolving motor problem quickly in order to prevent catastrophic failure of electrical motor. The training methodology is theory and practical, where the participants will be actively involved in the hands-on activities. Best practice motor maintenance and detailed case studies will also be discussed during the course. At the end of the course, the participants will achieve sound knowledge in motor maintenance in order to reduce motor failure rate by extending its life span, thus reducing the cost of the overall motor maintenance cost.
Objective:
Upon completion of this course, participants will be able to:

  • Identify various types of motors and its constructions
  • Conduct required motor maintenance and testing
  • Locate and rectify motor problems
  • Perform various tests on the motor


for any enquiries please contact:

1. NAME: YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: SOH LEY BAU
   Email: sohlb@tnb.com.my

Target Participant: TNB Generation Technician TT07-TT10 & Engineer
Duration: 2 Days
Language: English, Malay

RM 3.6K
Motor Testing and Maintenance
Power & Energy

2 Days

View Details

Overview:
The course provides a comprehensive knowledge about the Motor Maintenance and Testing in power plant and industry environment. The targeted audience of this course are power plant electrical engineers, facility engineers and technical supervisors whose jobs involve in the maintenance of electrical motor.

This course covers the competency requirements to recognize, diagnose and remedy an evolving motor problem quickly in order to prevent catastrophic failure of electrical motor. The training methodology is theory and practical, where the participants will be actively involved in the hands-on activities. Best practice motor maintenance and detailed case studies will also be discussed during the course. At the end of the course, the participants will achieve sound knowledge in motor maintenance in order to reduce motor failure rate by extending its life span, thus reducing the cost of the overall motor maintenance cost.
Objective:
Upon completion of this course, participants will be able to:

  • Identify various types of motors and its constructions
  • Conduct required motor maintenance and testing
  • Locate and rectify motor problems
  • Perform various tests on the motor


Target Participant: OPEN
Duration: 2 Days
Language: English, Malay

RM 3.6K
Non-Destructive Testing: Application of Liquid Penetrant…
Power & Energy

4 Days

View Details

Overview:
The course is designed to improve participant’s skill to carry out and monitor Non Destructive Testing – Liquid Penetrant Testing Method performed by the Inspector. The trainers will guide and facilitate the participants, so that they can to improve their ability to perform effective monitoring and Liquid Penetrant Inspection.

The training format is theory and practical, where the participants will be actively involved in the class and practical activities. Hence, it will increase their confidence level.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experience of training by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
Select the best technique and perform the test on power plants and mechanical components by using Liquid Penetrant Testing Method to detect surface discontinuities and defects in accordance with Codes, Standards and Specifications used.


for any enquiries please contact:

1. NAME: AMIR BIN ABU
   Email: amira@tnb.com.my

Target Participant: Mechanical Engineer, QA/QC Engineers, QA/QC Inspector, Technical Executive & Maintenance Technician
Duration: 4 Days
Language: English, Malay

RM 3.6K
Non-Destructive Testing: Application of Liquid Penetrant…
Power & Energy

4 Days

View Details

Overview:
The course is designed to improve participant’s skill to carry out and monitor Non Destructive Testing – Liquid Penetrant Testing Method performed by the Inspector. The trainers will guide and facilitate the participants, so that they can to improve their ability to performed effective monitoring and inspection using Liquid Penetrant Inspection.

The training format is theory and practical, where the participants will be actively involved in the class activities. Hence, it will increase their confidence level.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experience of training by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
Select the best technique and perform the test on power plants and mechanical components by using Liquid Penetrant Testing Method to detect surface discontinuities and defects in accordance with Codes, Standards and Specifications used.


for any enquiries please contact:

1. NAME: AMIR ABU
   Email: amira@tnb.com.my

Target Participant: Mechanical Engineer, QA/QC Engineers, QA/QC Inspector, Technical Executive & Maintenance Technician
Duration: 4 Days
Language: English, Malay

RM 3.6K
Non-Destructive Testing: Application of Magnetic Particle…
Power & Energy

5 Days

View Details

Overview:
This course is designed to explain the basic criteria for Identify material processes and classification of defects, state physical principle of the test, list out advantages and limitations, Identify testing technique and testing equipment, and then carry out the test in accordance with Codes, Standards and Specifications (ASME Section V), Select the most appropriate testing technique for the inspection and able to prepare testing procedure, Identify and evaluate discontinuities and defects in accordance with Codes, Standards and Specifications given (ASME) and Adhere safety precautions in Magnetic Particle Testing.

The training format is theory and practical, where the participants will be actively involved in the class & workshop activities. Hence, it will increase their confidence level.

Participant will be taken through the vast experience of magnetic particles testing methods in power plants inspection procedure and performance by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
After attending this program, participants will be able to:

Select the best technique and perform the test on power plants and mechanical components by using Magnetic Particles Testing Method to detect surface / sub surface discontinuities and defects in accordance with Codes, Standards and Specifications used.


for any enquiries please contact:

1. NAME: AMIR ABU
   Email: amira@tnb.com.my

Target Participant: Technicians, Mech. Engineers, Mech. Executives, Mech. Non-Executives & QA/QC Engineers
Duration: 5 Days
Language: English, Malay

RM 3.6K
Non-Destructive Testing: Application of Magnetic Particle…
Power & Energy

4 Days

View Details

Overview:
This course is designed to explain the basic criteria for Identify material processes and classification of defects, state physical principle of the test, list out advantages and limitations, Identify testing technique and testing equipment, and then carry out the test in accordance with Codes, Standards and Specifications (ASME Section V), Select the most appropriate testing technique for the inspection and able to prepare testing procedure, Identify and evaluate discontinuities and defects in accordance with Codes, Standards and Specifications given (ASME) and Adhere safety precautions in Magnetic Particle Testing.

The training format is theory and practical, where the participants will be actively involved in the class & workshop activities. Hence, it will increase their confidence level.

Participant will be taken through the vast experience of magnetic particles testing methods in power plants inspection procedure and performance by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
After attending this program, participants will be able to:

Select the best technique and perform the test on power plants and mechanical components by using Magnetic Particles Testing Method to detect surface / sub surface discontinuities and defects in accordance with Codes, Standards and Specifications used.


for any enquiries please contact:

1. NAME: AMIR ABU
   Email: amira@tnb.com.my

Target Participant: Technicians, Mech. Engineers, Mech. Executives, Mech. Non-Executives & QA/QC Engineers
Duration: 4 Days
Language: English, Malay

Human Resource Minister - Training Provider Award 2007
Role Model Company 2013 for Electrical Training Programmes by Manpower Department (JTM)
Energy Industry Award: Training Institution Excellence 2011

TNB Integrated Learning Solution Sdn Bhd - ILSAS
Jalan IKRAM-UNITEN, Karung Berkunci 205,
43650 Bandar Baru Bangi, Selangor, MALAYSIA

T: (+6) 03-8922 7222 F: (+6) 03-8926 4437 E: infoilsas@tnb.com.my

© 2017 TNB ILSAS