Power & Energy

RM 3.6K
City and Guilds - Combined Cycle Power Plant Operations…
Power & Energy

10

View Details

Overview:

Objective:


Target Participant: Non-exec & Exec
Duration: 10
Language:

RM 3.6K
City and Guilds - Combined Cycle Power Plant Operations…
Power & Energy

10

View Details

Overview:

Objective:


Target Participant: Non-exec & Exec
Duration: 10
Language:

RM 3.6K
Coal Technology
Power & Energy

3 Days

View Details

Overview:
This course offers for participants to describe the analysis of coal in plant operation. Its topic consists of introduction of coal as fuel, performance evaluation of coal and energy efficiency opportunities.
Participant will be taken through the vast experience of this course. The emphasis is on participants continuing participation in ensuring the ultimate success of the courses.
Objective:
At the end of the course the participant will be to:

  • Explain the type of coal as a fuel
  • Describe the coal analysis and its utilization
  • State the coal combustion
  • Explain the fundamental of plant efficiency


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.com.my

Target Participant: Thermal Power Plant Operations, Lab Technicians, Maintenance Technicians, and Engineers & those who are interested to deepen their knowledge about the subject
Duration: 3 Days
Language: English, Malay

RM 3.6K
Combined Cycle Gas Turbine (CCGT) Power Plant Shutdown…
Power & Energy

2 Days

View Details

Overview:

This course offers for participants to explain and perform the combined cycle gas turbine operation shutdown using simulator. Its consists of introduction to combined cycle gas turbine shutdown (normal and half block); requirement and preparation before shutdown; operational outline of shutting down combined cycle gas turbine power plant; limitation during shutdown and the needs of emergency shutdown.

Participant will be taken through the vast experience of this course. The emphasis is on participants continuing participation in ensuring the ultimate success of the courses.

 


Objective:
At the end of the course the participant will be able to:
  • Explain Combined Cycle Gas Turbine Shutdown preparation
  • Perform Combined Cycle Gas Turbine Normal Full Block Shutdown using simulator
  • Perform Combined Cycle Gas Turbine Normal Half Block Shutdown using simulator
  • Perform Combined Cycle Gas Turbine Emergency Shutdown situation using simulator

for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI B. MOHD SALLEH
     Email: khairul.fikri@tnb.com.my
 

Target Participant: TT09 - 12
Duration: 2 Days
Language:

RM 3.6K
Combined Cycle Gas Turbine (CCGT) Power Plant Start-up…
Power & Energy

3 Days

View Details

Overview:

This course offers for participants to explain and perform the combined cycle gas turbine operation start-up using simulator. Its consists of Human-Machine Interface (HMI) familiarization and simulator configuration; combined cycle pre start-up preparation; gas turbine and HRSG start-up; HRSG start-up & pressure raising; steam turbine start-up & TSI monitoring; load increasing, load decreasing & AUX change over; and line voltage control, frequency control, field voltage control.

Participant will be taken through the vast experience of this course. The emphasis is on participants continuing participation in ensuring the ultimate success of the courses.


Objective:
On completion of the course, participant will be able to:

• Perform the block cold start up using simulator
• Start HRSG using simulator
• Start up the two Gas Turbine (GT) and Steam Turbine (ST) and increase load to full load using simulator
• Explain the working principles of combined cycle system
• Explain the operation of GT, Heat Recovery Steam Generator (HRSG),ST, Balance of Plant (BOP), e.g. start-up, synchronizing, supervision, protection and shutdown
• Describe type of routine operation (change over of auxiliary system)
• Explain the critical operation event


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI B. MOHD SALLEH
     Email: khairul.fikri@tnb.com.my
 

Target Participant: TT09 - 12
Duration: 3 Days
Language:

RM 3.6K
Combined Cycle Gas Turbine (CCGT) Power Plant Start-Up…
Power & Energy

3 Days

View Details

Overview:
This course offers for participants to explain and perform the combined cycle gas turbine operation start-up using simulator.  Its consists of Human-Machine Interface (HMI) familiarization and simulator configuration, combined cycle pre start-up preparation, gas turbine and HRSG start-up, HRSG start-up and pressure raising, steam turbine start-up and TSI monitoring, load increasing, loasd increasing and AUX change over, and line voltage control, frequency control, field voltage control.

Participant will be taken through the vast experience of this course.  The emphasis is on participants continuing participation in ensuring the ultimate success of the courses.
Objective:
On completion of the course, participant will be able to:

  • Perform the block cold start up using simulator
  • Start HRSG using simulator
  • Start up the two Gas Turbine (GT) and Steam Turbine (ST) and increase load to full load using simulator
  • Explain the working principles of combined cycle system
  • Explain the operation of GT, Heat Recovery Steam Generator (HRSG),ST, Balance of Plant (BOP), e.g. start-up, synchronizing, supervision, protection and shutdown
  • Describe type of routine operation (change over of auxiliary system)
  • Explain the critical operation event

for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.com.my

Target Participant: TNB Generation Technician TT09-TT12
Duration: 3 Days
Language:

RM 3.6K
Combustion Technology
Power & Energy

3 Days

View Details

Overview:

This course offers for participants to operate the boiler in efficient manner in compliance to optimal operating and environmental requirement. Its consists of boilers and combustion; fuel for power generation; combustion for power generation; emission and environmental performance.

Participant will be taken through the vast experience of this course. The emphasis is on participants continuing participation in ensuring the ultimate success of the courses.


Objective:

Terminal Objective:

The participant will be able to operate the boiler in efficient manner in compliance to optimal operating condition and environmental requirement.

Course Objectives:

At the end of the course the participant will be to:

  • Explain on general boiler main components
  • Explain boiler draft system
  • Discuss burner set up
  • Explain coal pulverizer system
  • Describe the PPA clause related to heat rate requirement
  • Describe the correct fuel specification, terminology and handling process required for combustion process
  • Evaluate the different effects on boiler and mills operation for a given fuel type
  • Monitor and control power plant emission in accordance to regulatory standards and plant operating limit


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI B. MOHD SALLEH
     Email: khairul.fikri@tnb.com.my
 



Target Participant: TT11 - 13
Duration: 3 Days
Language:

RM 3.6K
Combustion Technology
Power & Energy

3 Days

View Details

Overview:
This course offers for participants to  operate the boiler in efficient manner in compliance to optimal  operating  and  environmental  requirement.  Its  consists  of  boilers  and  combustion;
fuel  for  power  generation;  combustion  for  power  generation;  emission and environmental performance.

Participant  will  be  taken  through  the  vast  experience  of  this  course.  The  emphasis  is  on participants continuing participation in ensuring the ultimate success of the courses.
Objective:
Terminal Objective:

The participant will be able to operate the boiler in efficient manner in compliance to optimal operating condition and environmental requirement.

Course Objectives:

At the end of the course the participant will be to:

  • Explain on general boiler main components
  • Explain boiler draft system
  • Discuss burner set up
  • Explain coal pulverizer system
  • Describe the PPA clause related to heat rate requirement
  • Describe the correct fuel specification, terminology and handling process required for combustion process
  • Evaluate the different effects on boiler and mills operation for a given fuel type
  • Monitor and control power plant emission in accordance to regulatory standards and plant operating limit


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.com.my

Target Participant: TNB Generation Technician TT11-TT13
Duration: 3 Days
Language:

RM 3.6K
Compressor Maintenance and Technology
Power & Energy

3 Days

View Details

Overview:
This course will cover basic compressor concepts, and provides an overview of all different types of compressor along with its' application in the industry.  The main bulk of the training will emphasis on maintenance activity, trouble-shooting, and an actual overhaul of a typical crosshead reciprocating compressor.   This will include disassembly, measurement, inspection, and reassembly.

Participant will be required to study with instructor guidance in order to present on the result of measurement and inspection, an overall components review, detail of lubrication systems, air delivery & control, and cooling systems.

Also covered are the components, typical maintenance problems, control and regulation of a typical compressor air system.
Objective:

  • Describe the types and functions of a compressor
  • List down all parts in an air compressor system
  • Carry out routine maintenance and inspection of a reciprocating compressor correctly
  • Overhaul a reciprocating compressor with recommended procedures, measurement, and inspections
  • Identify different types of compressor and applications


Target Participant: Engineer & Exec
Duration: 3 Days
Language: English, Malay

RM 3.6K
Compressor Maintenance Technology
Power & Energy

3 Days

View Details

Overview:
This course will cover basic compressor concepts, and provides an overview of all different types of compressor along with it's application in the industry. The main bulk of the training will emphasis on maintenance activity, trouble-shooting, and an actual overhaul of a typical crosshead reciprocating compressor. This will include disassembly, measurement, inspection, and reassembly.

Participant will be required to study with instructor guidance in order to present on the result of measurement and inspection, an overall components review, detail of lubrication systems, air delivery & control, and cooling systems. Also covered are the components, typical maintenance problems, control and regulation of a typical compressor air system.
Objective:
· Describe the types and functions of a compressor
· List down all parts in an air compressor system
· Carry out routine maintenance and inspection of a reciprocating compressor correctly
· Overhaul a reciprocating compressor with recommended procedures, measurement, and inspections
· Identify different types of compressor and applications


for any enquiries please contact:

1. NAME: CHOOI WAI MUN
   Email: chooiwm@tnb.com.my

2. NAME: ABDUL RAZAK
   Email: razakm@tnb.com.my

Target Participant: TNBG Mechanical Maintenance
Duration: 3 Days
Language: English, Malay

RM 3.6K
Computer Simulation of Gas Turbines
Power & Energy

3 Days

View Details

Overview:
This seminar provides indepth understanding of computer simulation of gas turbines under steady-state and transient conditions.  The selection considerations and applications of co-generation and combined cycles are also covered in this seminar.  The analysis performed by gas turbine simulators provides the following benefits:

1. Allow the operator to extend the gas turbine operating period by avoiding unnecessary outages and maintenance activities.
2. Determination of essential gas turbine maintenance activities to reduce the duration of the outage.
Objective:
To provide a comprehensive understanding of computer simulation of gas turbines, as well as their selection criteria, operation and maintenance requirements, and economics.  Participants will develop a good understanding of gas turbines and their numerous advantages.

• Gain a thorough understanding of computer simulation on gas turbines
• Learn about all components and subsystems of the various types of gas turbines
• Examine the advantages, applications, performance and economics of gas turbines 
• Learn about various equipment including compressors, turbines, governing systems, combustors, heat recovery steam generators, and auxiliaries
• Learn about the monitoring and control of environmental emissions
•  Gain a thorough understanding of the selection considerations and applications of co-generation and combined cycles


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my
2. NAME: MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.com.my

Target Participant: Engineers of all disciplines, Managers, Technicians, Maintenance personnel & other technical individuals
Duration: 3 Days
Language:

RM 3.6K
Condition Monitoring (TT09-TT13)
Power & Energy

4 Days

View Details

Overview:
This course on condition monitoring emphasis the importance and understanding what is truly the concept of condition monitoring based on maintenance and the advantages of using this system. Participants will be introduced to various technologies used at a typical power plant for condition monitoring such as Thickness gauging, Ultrasound, Penetrant Testing, Magnetic Particle Testing, Radiography Inspection, Oil Analysis, Motor Current Signature Analysis, Vibration Analysis, Infrared Thermography, & acoustic ultrasound.

Emphasis on 3 key condition monitoring technologies (Infrared Thermography, Vibration Analysis, and Airborne Ultrasound) will be covered in the bulk of the course. This will give a comprehensive understanding of the principles of the technologies in order to appreciating its' advantages and limitations.
Objective:

  • Describe what is condition monitoring
  • List the important of condition monitoring
  • Identify methods of condition monitoring
  • Perform data collection on vibration monitoring
  • Learn the use and limitations of Infrared Thermal imaging and measurement devices
  • Identify possible applications of Airborne Ultrasound

for any enquiries please contact:

1. NAME: CHOOI WAI MUN
   Email: chooiwm@tnb.com.my

2. NAME: ABDUL RAZAK
   Email: razakm@tnb.com.my

Target Participant: TNBG Mechanical Maintenance (TT09-TT13)
Duration: 4 Days
Language: English, Malay

RM 3.6K
Control Valve for Plant Process
Power & Energy

3 Days

View Details

Overview:
The course is designed to improve participant’s skill to Calibration and maintenance of Pneumatic Control Valve in their’s working place.

The training format is on theory and practical, where the participants will be actively involved in the lab activities.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experiences of training by the trainer. The emphasis is on participants continuing participation in ensuring the ultimate success in the course. 
Objective:
After attending this training program, participants will be able to:

  • Identify types of control valves and actuators.
  • Calibrate and maintain pneumatic valve actuators.
  • Calibrate valve positioner.
  • Troubleshoot valve system common problems.
Without any mistake.


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: TAN BENG WEE
   Email: tanbw@tnb.com.my

Target Participant: Control & Instrumentation personnel & individuals or technicians involved in maintenance of process measurement
Duration: 3 Days
Language: English, Malay

RM 3.6K
Conventional Power Plant Operation
Power & Energy

3 Days

View Details

Overview:
It is a topic that  will enable technicians to identify the principles of thermodynamics related to thermal power plant. Besides knowing the associated system in power plant such as coal handling system,  major components of boiler and steam turbine, general auxiliaries for boiler and turbine in coal power plant together with its operation and ash handling system.
Objective:

Terminal Objective:

With the notes given, participant will be able to explain the operation of conventional coal power plant and its auxiliaries correctly.

Course Objectives:

On completion of the course, participants will be able to describe:

  • The operation of conventional coal power plant.
  • The systems that associated with coal firing.
  • The auxiliary systems handling with coal, ash and power generation.
  • The basics operation principles using coal simulator.


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI B. MOHD SALLEH
     Email: khairul.fikri@tnb.com.my
 
 



Target Participant: TT07-12
Duration: 3 Days
Language:

RM 3.6K
Conventional Power Plant Operation
Power & Energy

3 Days

View Details

Overview:
It is a topic that  will enable technicians to identify the principles of thermodynamics related to thermal power plant. Besides knowing the associated system in power plant such as coal handling  system,  major  components  of  boiler  and  steam  turbine, general  auxiliaries  for boiler and turbine in coal power plant together with its operation and ash handling system.
Objective:
Terminal Objective:

With the notes given, participant will be able to explain the
operation of conventional coal power plant and its auxiliaries
correctly.

Course Objectives:

On completion of the course, participants will be able to describe:
· The operation of conventional coal power plant.
· The systems that associated with coal firing.
· The auxiliary systems handling with coal, ash and power generation.
· The basics operation principles using coal simulator.


for any enquires please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI BIN MOHD SALLEH
   Email: khairul.fikri@tnb.com.my

Target Participant: TNB Generation Technician TT07-TT12 & those who are interested to deepen their knowledge about the subject
Duration: 3 Days
Language:

RM 3.6K
Conventional Power Plant Shutdown with Simulation
Power & Energy

2 Days

View Details

Overview:

It is a topic on 300MW coal fired power plant simulation course; identifying the panel familiarization sequence of events for unit normal shutdown; sequence of events of normal shutdown on coal; boiler forced cooled procedure and turbine forced cooled procedure.

 


Objective:
Terminal Objective:

With the simulator, participant will be able to shut down the unit on 300MW coal simulator without mistake.

Course Objectives:

At the end of the course, participants will be able to:
  • List out the difference between unit normal shutdown and unit forced cooled shutdown.
  • List sequence of events during unit normal shutdown.
  • Shutdown the unit from full load using simulator.
  • Explain the importance of boiler and turbine forced cooled shutdown.
  • Describe all the procedures involve in boiler and turbine forced cooled shutdown
  • Prepare the boiler and turbine by following boiler and turbine forced cooled shutdown procedures by using coal simulator.
 
for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI B. MOHD SALLEH
     Email: khairul.fikri@tnb.com.my
 

Target Participant: TT09 - 12
Duration: 2 Days
Language:

RM 3.6K
Conventional Power Plant Start-up with Simulation
Power & Energy

3 Days

View Details

Overview:
It is a topic on 300MW coal fired power plant simulation course; identifying the panel familiarization sequence of events for Hot Start Up on Coal firing. Determining the cold, warm, hot and very hot procedures based on the time duration of start up for different conventional power plant within TNB.
Objective:

Terminal Objective:

With the simulator, participant will be able to start the unit on hot using 300MW coal simulator without mistake.

Course Objectives:

At the end of the course, participants will be able to:

  • Identify the start up condition - Cold, Warm, Hot and Very Hot Start Up
  • Explain the operation outline of start up events during Cold, Warm, Hot and Very Hot Start Up
  • Access and analyze important parameters via monitor during Hot Start Up
  • Start the unit on Hot Start using 300MW Coal Simulator within stipulated time frame with no delay and mistakes


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my

2. NAME: MOHD KHAIRUL FIKRI B. MOHD SALLEH
     Email: khairul.fikri@tnb.com.my
 
 



Target Participant: TT09 - 12
Duration: 3 Days
Language:

RM 3.6K
Distributed Control System (DCS) and Programmable…
Power & Energy

3 Days

View Details

Overview:
The course is designed to improve participant’s skill on the fundamental of Distributed Control System and also basic knowledge on Programmable Logic Controller (Siemens) in their’s working place.

The training format is on theory and practical, where the participants will be actively involved in the lab activities.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experiences of training by the trainer. The emphasis is on participants continuing participation in ensuring the ultimate success in the course.
Objective:

After attending the training program, participants will be able to:
 
• Identify and explain the functions of DCS system module and components.
• Define and describe hardware set up of modules and termination units in a system.
• Draw the PLC block diagram including processor unit, memory, the power supply unit, input and output interface and the programming device
• Explain and draw the logic function
• Design and develop ladder program

Without any mistake.


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: TAN BENG WEE
   Email: tanbw@tnb.com.my

Target Participant: Control & Instrumentation personnel & individuals o technicians involved in maintenance of process measurement
Duration: 3 Days
Language:

RM 3.6K
Distributed Control System (DCS) Configuration
Power & Energy

2 Days

View Details

Overview:
The course is designed to improve participant’s skill to DCS Configuration in their’s working place.

The training format is on theory and practical, where the participants will be actively involved in the lab activities.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experiences of training by the trainer. The emphasis is on participants continuing participation in ensuring the ultimate success in the course.
Objective:
At the end of this training program, participants will be able to:

  • Describe the aspects of configuring a distributed control system (DCS)
  • Explain the procedure, equipment, and software aspects of configuration
  • Perform DCS control scheme modification/configuration

Without any mistake.


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: TAN BENG WEE
   Email: tanbw@tnb.com.my

Target Participant: Control & Instrumentation personnel TT10-TT14 & individuals or technicians involved in maintenance of process measurement
Duration: 2 Days
Language: English, Malay

RM 3.6K
Electrical Protection System
Power & Energy

4 Days

View Details

Overview:

The course is designed to improve participant’s knowledge to work out on:

• Definition of protection
• Purpose of protection   
• Requirement of  protection
• Protection scheme
• Types of faults
• Types of protection
• Classification of relay
• Performance test & evaluation

The trainers will guide and facilitate the participants. The training format is theoretical and there will be a visit to protection laboratory in ILSAS.


Objective:

Upon completion of this course, participants will be able to:

• Describe the purpose of protection
• Explain the protection’s requirements
• Describe the various types of protection
• Explain the types of electrical faults
• List the various types of protection relays
• Explain the basic fundamental of relays

accurately by referring to slides / notes given.


for any enquiries please contact:

1. NAME: ABDUL HISHAM ABDUL HALIM
     Email: ahisham.ahalim@tnb.com.my

2. NAME: YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my
 



Target Participant: TT 11-13 (Thermal) TT 07-13 (Hydro)
Duration: 4 Days
Language:

RM 3.6K
Electrical Protection System
Power & Energy

4 Days

View Details

Overview:
The course is designed to improve participant’s knowledge to work out on:

  • Definition of protection
  • Purpose of protection
  • Requirement of  protection
  • Protection scheme
  • Types of faults
  • Types of protection
  • Classification of relay
  • Performance test & evaluation

The trainers will guide and facilitate the participants. The training format is theoretical and there will be a visit to protection laboratory in ILSAS.
Objective:
Upon completion of this course, participants will be able to:
  • Describe the purpose of protection
  • Explain the protection’s requirements
  • Describe the various types of protection
  • Explain the types of electrical faults
  • List the various types of protection relays
  • Explain the basic fundamental of relays

Accurately by referring to slides / notes given.


for any enquiries please contact:

1. NAME: ABDUL HISHAM ABDUL HALIM
   Email: ahisham.ahalim@tnb.com.my

2. NAME: YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

Target Participant: TNB Generation Technician TT11-TT14 (Generation Operation-Thermal) & TT07-TT14 (Generation Operation-Hydro)
Duration: 4 Days
Language:

RM 3.6K
Electrical System Operation
Power & Energy

5 Days

View Details

Overview:
This course will provide the principles application of switching operation & switching procedures and communication skill with National Load Dispatch Centre (NLDC). The goal of the course is to give generation operation personal to familiarize responsibilities and perform safe working environment of electrical switching operation under NLDC’s instructions.

The trainers will guide and facilitate the participants. The training format is theoretical class and practical training.
 
Objective:
Upon completion of this course, participants will be able to:

• Describe the definition of generator
• Describe the principles of operation
• Describe the definition of synchronizing
• Retrieve information from the electrical parameters
• Write the Switching Operation Procedures in order
• Describe and carry out the Switching Operation correctly and safely of the plant and personnel.

by referring to slides / notes given.


for any enquiries please contact:

1. NAME: ABDUL HISHAM ABDUL HALIM
     Email: ahisham.ahalim@tnb.com.my

2. NAME: YEOH CHIEN WERN
     Email: yeohcw@tnb.com.my

Target Participant: TT 11-13 (Thermal) TT 07-13 (Hydro)
Duration: 5 Days
Language:

RM 3.6K
Electrical System Operation
Power & Energy

5 days

View Details

Overview:
This course will provide the principles  application  of switching operation & switching procedures and communication skill with  National Load Dispatch Centre (NLDC). The goal of the course is to  give  generation  operation  personal  to  familiarize  responsibilities  and  perform  safe  working environment of electrical switching operation under NLDC’s instructions.

The trainers will guide and facilitate the participants. The training format is theoretical class and practical training.
Objective:
Upon completion of this course, participants will be able to:

  • Describe the definition of generator
  • Describe the principles of operation
  • Describe the definition of synchronizing
  • Retrieve information from the electrical parameters
  • Write the Switching Operation Procedures in order
  • Describe and carry out the Switching Operation correctly and safely of the plant and personnel.

by referring to slides / notes given.


for any enquiries please contact:

1. NAME: ABDUL HISHAM ABDUL HALIM
   Email: ahisham.ahalim@tnb.com.my

2. NAME: YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

Target Participant: TNB Generation Technician TT11-TT14 (Generation Operation -Thermal) & TT07-TT14 (Generation Operation-Hydro)
Duration: 5 days
Language:

RM 3.6K
Emergency Preparedness and Response
Power & Energy

3 Days

View Details

Overview:
This course is designed to explain the basic criteria for define overall requirement of EPR, describe Emergency Management, describe roles & functions of ICS, describe preventive measures, demonstrate Emergency Response Plan and explain the requirement of training and exercise.

The training format is theory and practical, where the participants will be actively involved in the class & workshop activities. Hence, it will increase their confidence level.

Participant will be taken through the vast experience of emergency preparedness and response plan procedure and performance by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
After attending this training program, participants will be able to:

1. To define overall requirement of EPR.
2. To describe Emergency Management.
3. To describe roles & functions of ICS.
4. To describe preventive measures.
5. To demonstrate Emergency Response Plan.
6. To explain the requirement of training and exercise.


for any enquiries please contact:

1. NAME: AMIR ABU
   Email: amira@tnb.com.my

Target Participant: Technicians, Mech. Engineers, Mech. Executives & Mech. Non-Executive
Duration: 3 Days
Language: English, Malay

RM 3.6K
Energy Management - (cross fuction with OHSE & CORPORATE…
Power & Energy

1

View Details

Overview:

Objective:


Target Participant: TT07-TT11 & PP05
Duration: 1
Language:

RM 3.6K
Energy Measurement and Tariff
Power & Energy

2 Days

View Details

Overview:
It is important to know how to calculate energy consuming and learn how to provide and maintain a metering system that ensures efficient collation and assimilation of transaction and customer data. This is done by having an acute awareness of the classification and types of tariff.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experience of training by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
Upon completion of this course, participants will be able to:

  • Define power and energy
  • Calculate energy consuming
  • Differentiate types of tariff
  • Differentiate types of energy meter
  • State the steps of wiring and meter installation

for any enquiries please contact:

1. NAME: IR. WAN AMINUDDIN BAKI BIN ABDUL KHALID
   Email: aminuddinak@tnb.com.my

2. NAME: ANNAS BIN AHMAD SALLEH
   Email: annass@tnb.com.my

Target Participant: Executive and Non-Executive in Operational and Maintenance of Metering
Duration: 2 Days
Language: English, Malay

RM 3.6K
Factories and Machinery Act 1967
Power & Energy

3 Days

View Details

Overview:
This course is designed to explain the basic fundamentals and important aspects of Factories and Machinery Act 1967 (FMA 1967). Participants will be guided in reviewing all the parts under FMA 1967 and some important regulations under this Act.

The training format is theoretical, where the participants will be actively involved in the class & discussion activities. Hence, it will increase their confidence level in utilizing this FMA 1967.

Participant will be taken through the vast experience of this act by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
After attending this course, participants will be able:

  • To secure the safety, health and welfare of persons at work against risks to safety and health arising out the activities of persons at work through obligation and practicing the Act and Regulations.
  • To protect workers at a place of work and others at work against risks to safety or health arising of the activities of persons at work.
  • To promote an occupational environment for persons at work which is adapted to their physiological and psychological needs.
  • To provide the means where by the associated Occupational Safety & Health legislations may be progressively replaced by a system of regulations and approved industry codes of practice operating in combination with the provisions of this Act designed to maintain or improve the standards of safety and Health.


for any enquiries please contact:

1. NAME: CHOOI WAI MUN
   Email: chooiwm@tnb.com.my

Target Participant: TNBG Executives and Non-Executives in Operation & Maintenance
Duration: 3 Days
Language: English, Malay

RM 3.6K
Fire Safety
Power & Energy

3 Days

View Details

Overview:
This course is designed to explain the basic criteria for enabled to react in a correct manner in the event of an outbreak of fire, to take appropriate measures for the safety of personnel and the place of work, enabled to use the fire appliances correctly, Enabled to state and demonstrate that he has acquired knowledge and skills, which will enable him to identify and correct defects and thus prevent fire from occurring and Enabled to define the concept and to list the Fire Protection Systems.

The training format is theory and practical, where the participants will be actively involved in the class & workshop activities. Hence, it will increase their confidence level.

Participant will be taken through the vast experience of fire safety procedure and performance by the trainers. The emphasis is on participants continuing participation in ensuring the ultimate success of the course.
Objective:
After attending this training program, participants will be able to:

1. Enabled to react in a correct manner in the event of an outbreak of fire, to take appropriate measures for the safety of personnel and the place of work.
2. Enabled to use the fire appliances correctly.
3. Enabled to state and demonstrate that he has acquired knowledge and skills, which will enable him to identify and correct defects and thus prevent fire from occurring.
4. Enabled to define the concept and to list the Fire Protection Systems.


for any enquiries please contact:

1. NAME: AMIR ABU
   Email: amira@tnb.com.my

Target Participant: Technicians, Mech. Engineers, Mech. Executives, Mech. Non-Executives
Duration: 3 Days
Language: English, Malay

RM 3.6K
Fundamental and Procedure of CNI Troubleshooting
Power & Energy

3 Days

View Details

Overview:
The course is designed to improve participant’s skill to carry out troubleshooting in their’s working place. Trainer will guide and facilitate participants as their doing their practices and observed their safety as part of the training.

The training format is on theory and practical, where the participants will be actively involved in the lab activities. Hence, it will increase their confidence level and safety awareness.

 “Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experiences of training by the trainer. The emphasis is on participants continuing participation in ensuring the ultimate success in the course.
 
Objective:
Upon completion of the course, participants will be able:

• Describe general troubleshooting technique and methodology
• Explain the fundamental flow of system troubleshooting
• Apply general troubleshooting steps to own work scope
• Explain the procedures of taking permit
• Apply Safety precaution and awareness when taking permit
• Make a PTW request with necessary steps
• Identify the importance of safety and work procedures
• Describe what is short circuit and how dangerous it could be
• Differentiate between fire and explosion
• Define what an accident is
• Explain why accidents happen
• Describe how to prevent accidents
• Use lab equipment and hand tools safely
• Use measuring tools such as multimeter properly
• Troubleshoot certain problems in the power plant Instrumentation system like field instruments, signal module, cabling


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
   Email: yeohcw@tnb.com.my

2. NAME: TAN BENG WEE
   Email: tanbw@tnb.com.my
 

Target Participant: Control & Instrumentation personnel TT09 & individuals or technicians involved in troubleshooting plant
Duration: 3 Days
Language:

RM 3.6K
Fundamental of Distributed Control System (DCS)…
Power & Energy

3 Days

View Details

Overview:
The course is designed to improve participant’s skill to Distributed Control System in their’s working place.

The training format is on theory and practical, where the participants will be actively involved in the lab activities.

“Learning by doing” is a basic principle adopted in this training. Participant will be taken through the vast experiences of training by the trainer. The emphasis is on participants continuing participation in ensuring the ultimate success in the course.
Objective:
After attending this training program, participants will be able to:

  • Explain the basic concepts and operation of a distributed control system (DCS).
  • Identify and explain the functions of DCS system module and components.
  • Define and understand hardware set up of modules and termination units in a system.
  • Set the modules for intended operation without any mistake.


for any enquiries please contact:

1. NAME: IR. YEOH CHIEN WERN
  Email: yeohcw@tnb.com.my

2. NAME: TAN BENG WEE
   Email: tanbw@tnb.com.my

Target Participant: Control & Instrumentation personnel TT09-TT10 & individuals or technicians involved in maintenance of process measurement
Duration: 3 Days
Language:

Human Resource Minister - Training Provider Award 2007
Role Model Company 2013 for Electrical Training Programmes by Manpower Department (JTM)
Energy Industry Award: Training Institution Excellence 2011

TNB Integrated Learning Solution Sdn Bhd - ILSAS
Jalan IKRAM-UNITEN, Karung Berkunci 205,
43650 Bandar Baru Bangi, Selangor, MALAYSIA

T: (+6) 03-8922 7222 F: (+6) 03-8926 4437 E: infoilsas@tnb.com.my

© 2017 TNB ILSAS